4-8 hours1-2 hours2-3 days24 hours3-4 hours7-10 days
Application temperature range
+5º C to +45º C
Service Temperature
-30º C to +80º C
Resistance to solvents, oil & alkalis
Excellent
Resistance to moisture
Excellent
Resistance to ageing
Excellent
VOC content
0 g/ liter
Test according to EN 13888/ ISO 13007:
DATA
STANDARD REQUIREMENT CG2 WA
RESULT
Compressive Strength(after 28days)
EN 12190:1999> 15 N/mm²
> 25 N/mm²
Tensile Adhesion Strength(after 28days)
EN 12004-2:2017> 1 N/mm²
> 1 N/mm²
Abrasion resistance(after 28days)
EN12808-2≤ 2000 mm³
175 ± 0.20 mm³
Flexural Strength(after 28days)
EN12808-3> 3.5 N/mm²
> 4 N/mm²
Linear Shrinkage(after 28days)
EN 12808-4≤ 2 mm/m
None(0 ± 0.02 mm/m)
Water absorption
@ 30 minutes
@ 240 minutes
@ 24 hours
EN 12808-5
≤ 5 g
≤ 10 g
≤ 10 g
Comply
0.76 g
0.76 g
0.76 g
Test according to ANSI 118.7:
DATA
STANDARD REQUIREMENT CG2 WA
RESULT
Tensile strength
3.45 N/mm2 (500psi)
Complies
Flexural strength @ 28 days
6.89 N/mm2 (1000psi)
Complies
Water absorption
<5.0%
Complies
Linear Shrinkage
<0.2%
Complies
Note:
* All values given are subject to 5-10% tolerance
* At +23°C and 50% relative humidity. Higher temperatures reduce, lower temperatures increase the times given.
* Properties listed above are only based on controlled laboratory samples and tests: Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.
TilePro Grout is a fine coloured highly polymer modified cement powder, containing very fine-graded aggregates, special polymers, additives and pigments which, when mixed with water, gives a smooth, easily applied creamy paste for clean grouting of ceramic tiles and natural stone. Itis formulated using the latest grout technology including hydrophobic, easy clean, and anti-bacterial properties.
Additional Information
Applicable Standards/ Compliance:
Packaging:
Colours:
Coverage/ Yield:
Tested according to
ANSI A118.7 (polymer modified cement grouts)
International ISO 13007 & EN 13888, classified as CG2 WA - improved (2) cementitious (C) grout (G) with good water (W) and abrasion (A) resistance
1kg, 5kg, 20 kg bags
22 standard color
200-White
201-Snow White
202-Moon White
203-Manhattan
204- Silk Beige
205-Flamingo
206-Jasmine White
211-Dusty Grey
212-Medium Grey
213-Ash Grey
214-Dark Grey
220-Black
230-Off White
231-Ivory
232-Beige
234-Cream
235-Dark Beige
237-Bahama Beige
238-Almond
239-Brick
240-Dark Brick
243-Terracotta
Water Mix Ratio: 25 to 27%
Yield:
1 kg bag
5 kg bag
20 kg bag
0.67 litres
3.38 litres
13.54 litres
Consumption calculation formula:
A+B
--------x W x D x 1.5 = (....) kg/m²
Ax B
A: length of tile/stone (mm)
B: width of tile/stone (mm)
D: depth of tile/stone (mm)
W: width of joint (mm)
* Coverage of Tile Pro Grout varies depending on the width of the joints, the size and thickness of the tiles.
Typical Applications
For Indoor and Outdoor use
For Walls, Floors and Ceilings
For Dry and Wet areas (example: bathrooms, kitchen, toilets, balconies)
For swimming pools, pool surrounds, wet rooms
For joint widths from 1-10mm
For all ceramic tiles, porcelain, glass & marble mosaic tiles
For all non-moisture-sensitive stone material (natural stones, marble, granite, agglomerates, etc.)
In public and commercial areas subject to frequent or permanent wetness
Before applying TilePro Grout, make sure that tile is set and that the adhesive has completely dried. Usually, wall joints between the tiles can be grouted after 4-8 hours and floor joints after 24 hours (standard tile adhesives) or 4-6 hours (fast-setting tile adhesives).
All joints to receive TilePro Grout should be well cleaned, dry, free from loose material, stain, oil or grease, any compounds affecting the bond Remove dust or other contaminants with an air blower. Do not clean tiles with acid cleaners. All loose particles of tile adhesive in the joint must be physically removed to at least 2/3 of the tile thickness. When the tiles are very porous & installed in very hot areas, wet the joints with clean water
Product Preparation
Mix the bag contents with 25 to 27% of clean cool water by adding the powder to a clean bucket gradually. The amount of water must be respected to avoid efflorescence over the surface of the grout. Mix with a mechanical stirrer at low speed (<300 rpm) for approx. 3 minutes. Allow the mix to rest for 2 minutes and then mix again, until a smooth, creamy and lump free consistency is achieved. If the mortar has become too stiff to work, it should be discarded and a new batch should be prepared.
Product Application
Fill the joints completely with adequate rubber grout rubber float, squeegee or a rubber sided or a plastic trowel, spread the mix to substrate evenly and in sufficient quantity. Best result can be obtained by filling the joints with grout and flushing the surface of the tile using a hard rubber float, working diagonally across the joints to both fill and compact the joints. All excess grout should be removed with same rubber float, while still fresh.
Movement joints, corner joints (floor/wall) and connection joints (fixtures/tiles, wood/tiles) may be sealed with the elastic silicone joint sealant from SealPro range
Where To Buy